ASUS 공유기 최신펌에서 외장하드 상태 불량 > NAS포럼

본문 바로가기
사이트 내 전체검색


회원로그인

네이버 아이디로 로그인 Sign in with googleSign in with kakao
자동로그인

ASUS 공유기 최신펌에서 외장하드 상태 불량
일반 |
김곱상
쪽지보내기 자기소개 아이디로 검색

작성일: 2016-11-21 09:43:52 조회: 2,169  /  추천: 0  /  반대: 0  /  댓글: 0 ]

본문

으로 문의메일을 보냈는데

 

결론은 공유기 리셋해보랍니다.

 

아래는 구글번역

라우터 USB 포트에 외장 하드 드라이브를 연결하는 중에 오류 메시지가 표시되는 것을 알고 있습니다.

불편을 드려 죄송합니다. 나는 너를 도울 수있는 것보다 더 행복 할 것이다.

이 경우 라우터를 하드 리셋하고 아래의 지침에 따라 라우터를 다시 구성하고 문제가 해결되는지 확인해야합니다.

라우터를 재설정하려면 라우터의 재설정 버튼을 30 초 동안 길게 누른 다음 놓으십시오. 이제 아래 단계에 따라 라우터를 다시 구성하십시오.

1 단계 : 인터넷 브라우저를 열고 주소 표시 줄에 '192.168.1.1/index.asp'를 입력하고 Enter 키를 누릅니다.

2 단계 : Username 필드에 'admin'을 입력하고 Password 필드에 'admin'을 입력하고 'Ok'를 선택하십시오. 이제 라우터의 정보 페이지로 이동하게됩니다.

3 단계 : 탐색 패널에서 고급 설정> 무선> 일반 탭으로 이동합니다.

4 단계 : 무선 네트워크의 주파수 대역으로 2.4GHz 또는 5GHz를 선택하십시오.

5 단계 : SSID (Service Set Identifier) ​​또는 네트워크 이름에 최대 32자를 포함하는 고유 한 이름을 지정하여 무선 네트워크를 식별합니다. Wi-Fi 장치는 할당 된 SSID를 통해 무선 네트워크를 식별하고 무선 네트워크에 연결할 수 있습니다. 새 SSID가 설정에 저장되면 정보 배너의 SSID가 업데이트됩니다.

6 단계 : 'SSID 숨기기'필드에서 '아니요'를 선택하면 SSID가 자동으로 감지됩니다.

7 단계 : 무선 모드 옵션에서 '자동'을 선택하십시오.

8 단계 : 더 높은 전송 속도를 수용하기 위해 이러한 채널 대역폭 중 하나를 선택하십시오.

(A) 20MHz (기본값) : 무선 연결에 문제가 발생하면이 대역폭을 선택하십시오.

(B) 40MHz : 무선 처리량을 최대화하려면이 대역폭을 선택하십시오.

9 단계 : 무선 라우터에 대한 제어 채널을 선택하십시오. '자동'을 선택하면 무선 라우터가 간섭량이 가장 적은 채널을 자동으로 선택할 수 있습니다.

10 단계 : 인증 방법을 WPA2- 개인으로 설정합니다 (이 옵션은 매우 강력한 보안 기능을 제공함).

11 단계 : WPA 암호화를 AES로 설정합니다.

12 단계 : WPA 사전 공유 키에 8 ~ 16 자의 영숫자를 입력합니다. 이것이 귀하의 SSID 암호입니다.

13 단계 : '적용'을 선택하고 라우터를 재부팅하십시오.​ 

 

아래는 원문

I understand that you are getting error message while connecting your external hard drive in router USB port.

I apologize for the inconvenience caused. I will be more than happy to help you.

In this case, I request you to hard reset the router and reconfigure it by following the instructions given below and check whether it resolves the issue.:

To reset the router, kindly press and hold the router’s Reset Button for 30 seconds and then release it. Now follow the steps below to reconfigure the router:

Step 1: Open your internet browser and type '192.168.1.1/index.asp' in the address bar and press ENTER.

Step 2: Type 'admin' in the Username field and 'admin' in the Password field and select ‘Ok’. Now, you will be in your router’s Information page.

Step 3: From the Navigation Panel, go to Advanced Settings > Wireless > General Tab

Step 4: Select 2.4GHz or 5GHz as the frequency band for your wireless network.

Step 5: Assign a unique name containing up to 32 characters for your SSID (Service Set Identifier) or Network Name to identify your wireless network. Wi-Fi devices can identify and connect to the wireless network via your assigned SSID. The SSIDs on the information banner are updated once new SSIDs are saved to the settings.

Step 6: In the ‘Hide SSID’ field, select 'No' to automatically detect your SSID.

Step 7: Select 'Auto' in the Wireless Mode option.

Step 8: Select any of these Channel Bandwidths to accommodate higher transmission speeds:

(A) 20MHz (default): Select this bandwidth if you encounter some issues with your wireless connection.

(B) 40MHz: Select this bandwidth to maximize the wireless throughput.

Step 9: Select the Control Channel for your wireless router. Choose ‘Auto’ to allow the wireless router to automatically select the channel that has the least amount of interference.

Step 10: Set Authentication Method to WPA2-Personal (This option provides very strong security).

Step 11: Set WPA Encryption to AES.

Step 12: Enter 8 to 16 alphanumeric characters in the WPA Pre-shared Key. This is your SSID's password.

Step 13: Then select ‘Apply’ and reboot the router.​ 


추천 0 반대 0

댓글목록

등록된 댓글이 없습니다.




리모컨

맨위로
 댓 글 
 목 록 
회사소개 개인정보처리방침 서비스이용약관 메일문의 Copyright © 딜바다닷컴 All rights reserved.
상단으로
모바일 버전으로 보기