Iomega ez 에 리눅스 커널 4.4 가 가능한것 같습니다. > NAS포럼

본문 바로가기
사이트 내 전체검색


회원로그인

네이버 아이디로 로그인 Sign in with googleSign in with kakao
자동로그인

Iomega ez 에 리눅스 커널 4.4 가 가능한것 같습니다.
정보 |
bonalk
쪽지보내기 자기소개 아이디로 검색

작성일: 2017-06-01 20:23:57 조회: 9,418  /  추천: 0  /  반대: 0  /  댓글: 0 ]

본문

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix1-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[[email protected]] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST340014AS                               Firm: 8.12     Ser#:             5MQ3ESZM
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi_flash:[email protected](u-boot),[email protected](env),[email protected](env2) earlyprintk=serial'
Marvell>> setenv bootcmd_usb 'usb reset; run usb_scan; printenv bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000'
Marvell>> run bootcmd_usb
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi_flash:[email protected](u-boot),[email protected](env),[email protected](env2) earlyprintk=serial
....
................................................................................................................................................................................................................................................................................................................

3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................

7179935 bytes read
## Booting image at 00040000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2017-06-01  10:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3167923 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes =  6.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

[    1.389166] console [ttyS0] enabled
[    1.396260] bootconsole [earlycon0] disabled
[    1.406813] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    1.417724] libphy: Fixed MDIO Bus: probed
[    1.422290] libphy: orion_mdio_bus: probed
[    1.430953] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.438915] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[    1.447932] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.454566] ehci-pci: EHCI PCI platform driver
[    1.459096] ehci-orion: EHCI orion driver
[    1.463345] orion-ehci f1050000.ehci: EHCI Host Controller
[    1.468882] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    1.476817] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    1.500144] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    1.506404] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.513252] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.520523] usb usb1: Product: EHCI Host Controller
[    1.525425] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[    1.532086] usb usb1: SerialNumber: f1050000.ehci
[    1.537536] hub 1-0:1.0: USB hub found
[    1.541378] hub 1-0:1.0: 1 port detected
[    1.546288] mousedev: PS/2 mouse device common for all mice
[    1.552580] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    1.559656] i2c /dev entries driver
[    1.565664] hidraw: raw HID events driver (C) Jiri Kosina
[    1.571531] drop_monitor: Initializing network drop monitor service
[    1.578081] NET: Registered protocol family 17
[    1.582844] Key type dns_resolver registered
[    1.587945] registered taskstats version 1
[    1.592136] Loading compiled-in X.509 certificates
[    1.597006] zswap: loaded using pool lzo/zbud
[    1.609539] Key type encrypted registered
[    1.614201] rtc-mv f1010300.rtc: setting system clock to 2017-06-01 11:04:09 UTC (1496315049)
[    1.625306] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[    1.697731] systemd-udevd[81]: starting version 215
[    1.712173] random: systemd-udevd urandom read with 2 bits of entropy available
[    1.860253] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    1.882374] SCSI subsystem initialized
[    1.936112] sata_mv f1080000.sata: slots 32 ports 2
[    1.979518] scsi host0: sata_mv
[    1.995654] scsi host1: sata_mv
[    1.999173] ata1: SATA max UDMA/133 irq 34
[    2.023876] ata2: SATA max UDMA/133 irq 34
[    2.028840] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[    2.040255] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.047461] usb 1-1: Product: USB Storage
[    2.063293] usb 1-1: Manufacturer: Generic
[    2.067528] usb 1-1: SerialNumber: 000000009451
[    2.087651] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.095135] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[    2.102183] scsi host2: usb-storage 1-1:1.0
[    2.108064] usbcore: registered new interface driver usb-storage
[    2.117078] usbcore: registered new interface driver uas
[    2.570155] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.610184] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[    2.615697] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    2.680186] ata1.00: configured for UDMA/133
[    2.700577] scsi 0:0:0:0: Direct-Access     ATA      ST340014AS       8.12 PQ: 0 ANSI: 5
[    3.060148] ata2: SATA link down (SStatus 0 SControl F300)
[    3.092503] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.103390] sd 0:0:0:0: [sda] Write Protect is off
[    3.108402] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.117737] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
[    3.136024] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.141939] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.148762]  sda: sda1
[    3.155907] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.266618] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    3.275227] sd 2:0:0:0: [sdb] Write Protect is off
[    3.281099] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.286451] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.299334]  sdb: sdb1
[    3.312373] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 43225/232000 files, 339950/927982 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Checking root file system...fsck from util-linux 2.20.1
rootfs: clean, 43225/232000 files, 339950/927982 blocks
done.
[ ok ] Cleaning up temporary files... /tmp.
[   16.773124] random: nonblocking pool is initialized
[....] Activating lvm and md swap...[   18.163144] Adding 524284k swap on /swapfile.  Priority:-1 extents:148 across:636112k FS
done.
[....] Checking file systems...fsck from util-linux 2.20.1
/dev/sda1: clean, 1205/2445984 files, 9108430/9764864 blocks
done.
[....] Mounting local filesystems...[   18.761442] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[....] Configuring network interfaces...Ignoring unknown interface lo=lo.
Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on   LPF/eth0/00:d0:b8:14:0b:8a
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
[   23.677688] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd only.
bound to 192.168.2.101 -- renewal in 34360 seconds.
done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix.
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting NTP server: ntpd.
[....] Starting ftp server: proftpdIOMEGA proftpd[1546]: mod_tls/2.4.3: compiled using OpenSSL version 'OpenSSL 1.0.1e 11 Feb 2013' headers, but linked to OpenSSL version 'OpenSSL 1.0.1t  3 May 2016' library
IOMEGA proftpd[1546]: mod_sftp/0.9.8: compiled using OpenSSL version 'OpenSSL 1.0.1e 11 Feb 2013' headers, but linked to OpenSSL version 'OpenSSL 1.0.1t  3 May 2016' library
IOMEGA proftpd[1546]: mod_tls_memcache/0.1: notice: unable to register 'memcache' SSL session cache: Memcache support not enabled
. ok
[ ok ] Starting Samba daemons:[....] Starting OpenBSD Secure Shell server: sshd.
[ ok  smbd.
/etc/rc.local: 16: /etc/rc.local: cannot create /sys/class/nasled/hdd1_link: Directory nonexistent
[FAIL] startpar: service(s) returned failure: rc.local ... failed!

Debian GNU/Linux 7 IOMEGA ttyS0

IOMEGA login:
 

 

커널 올리고 omv 설치하려고 합니다. 


추천 0 반대 0

댓글목록

등록된 댓글이 없습니다.




리모컨

맨위로
 댓 글 
 목 록 
회사소개 개인정보처리방침 서비스이용약관 메일문의 Copyright © 딜바다닷컴 All rights reserved.
상단으로
모바일 버전으로 보기